1952 Chevy Tail Pan fabrication

[MP&C]

Spent today hosting a Pullmax Workshop for some of the guys from the VA HAMB. OJ Higgins recently took delivery of a gargantuan Trumpf universal machine (a Pullmax on Steroids) and wanted a down and dirty on how these machines could be put to use. So OJ and a few other VA guys stopped by today and for a sample to use, ClutchDumpinDan brought by a tail pan from his 52 Chevy that was in dire need of rust repair.. We found a piece of 18 gauge cold rolled steel large enough to do the trick, so Dan cut it in half just in case we needed to do this twice...

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2461.jpg

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2462.jpg

Dies made for the universal tool holder in the Lennox Nibbler

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2468.jpg

Profile check...

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2465.jpg

Test sample...

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2467.jpg

Our new panel ready to run through the dies...

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2474.jpg

Step detail

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2483.jpg

Tipping the leading edge..

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2484.jpg

Dan takes a twinkie break

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2485.jpg

Videos....

https://www.youtube.com/watch?v=BB8wdKQHwqE

https://www.youtube.com/watch?v=lbrMeTq0HXE

https://www.youtube.com/watch?v=QWELebyXNF0

Comparing new to old...

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2493.jpg

Rusty seal joggle on the old panel...

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2494.jpg

The new one...

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2495.jpg

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2496.jpg

Adding some bead details to change things up a bit...

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2497.jpg

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2498.jpg

Comparison....

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2500.jpg

Fancy tool for finishing the bead ends...

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2503.jpg

[BamaNomad]

THAT is pretty impressive... :)

[MP&C]

Thanks!


Had some questions about how we did the "J" detail for the bumper seal..

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2496.jpg

I missed getting some of the pictures of the dies (how did that happen?), so had to go back afterwards...

These are all the dies used, I had three different lower dies to progressively fold the sides in. The location is set by using a backstop on the first pass, using the die show on the right..

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2517.jpg

This is the final die shown with a sample run...

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2487.jpg

http://i5.photobucket.com/albums/y167/rmccartney/Pullmax%20Workshop/IMG_2488.jpg

[markm]

Most of us just dream for cool toys like this and the talent to use them. Nice work.

[MP&C]

Doesn't seem like much got done this weekend, but here's what we did..




Stopped by the local CNC router facility to get some generic guides made for bead detail on the Lennox Nibbler...




http://i5.photobucket.com/albums/y167/rmccartney/Metalworking/IMG_2763.jpg




Also had some blanks cut out over there to the right side. These were to form stops so we can adjust length of our pattern shorter as needed..




http://i5.photobucket.com/albums/y167/rmccartney/Metalworking/IMG_2765.jpg




http://i5.photobucket.com/albums/y167/rmccartney/Metalworking/IMG_2766.jpg




It has a snug fit like so:




http://i5.photobucket.com/albums/y167/rmccartney/Metalworking/IMG_2767.jpg




Next was to turn up a new die with less crown than the other we've been using, just to have a different look, a flatter bead..




http://i5.photobucket.com/albums/y167/rmccartney/Metalworking/IMG_2770.jpg




http://i5.photobucket.com/albums/y167/rmccartney/Metalworking/IMG_2773.jpg




http://i5.photobucket.com/albums/y167/rmccartney/Metalworking/IMG_2775.jpg




Setting up for some practice runs...




http://i5.photobucket.com/albums/y167/rmccartney/Metalworking/IMG_2776.jpg




http://i5.photobucket.com/albums/y167/rmccartney/Metalworking/IMG_2777.jpg




Here's a comparison between the new die and the fuller radius we've been using..




https://www.youtube.com/watch?v=HMi7dYOM_VA&feature=youtu.be




Thursday night headed over to Virginia, the 52 Chevy tail pan now resided in Fredericksburg and I needed to borrow the original and new one for the Coming Out car show in Charlotte Hall, being held Sunday (today). I had been dragging my feet about even going to the show, but the weather forecast promised beautiful weather, so I went ahead and reserved a vendor spot to show off our fabrication work. Friday night started gathering some samples to take and a put some pictures together for an album..




http://i5.photobucket.com/albums/y167/rmccartney/Metalworking/IMG_2792.jpg




We still had all the original pieces for the lift gate repair, so that was a good sample..


Set up at the show, I figured parked next to the Ice Cream truck would be easier on my will power than the smell of three BBQ trucks on the other side...




http://i5.photobucket.com/albums/y167/rmccartney/Metalworking/IMG_2793.jpg




http://i5.photobucket.com/albums/y167/rmccartney/Metalworking/IMG_2794.jpg




Got these pictures right after we set up and before all the crowd showed up. Had a blast, talking metalshaping, rust repair, etc. for most of the day.. I guess I've got to get back to work now...

[MP&C]

We don't always get to see installed pictures of some of the smaller fabrications we do, so when it does happen it's nice to share them. The tailpan we made in this thread has been fitted up to the car, and I finally got a picture!


https://lh3.googleusercontent.com/tZ32dNLuwi1ip3Q_foxvtQ5W_PjrBdCCFMJ4L7O6BMplcclEv-qnoDuqj5ig4iHOUjY0D7G3N4ryHaFspdV1RKaBvcF8u1z0JNU5 JLjfbeP9zvPhXlKdJumWu-ezcO0ZhdQX9sIq3nLITWf9Vn3CWto_OX_yRDAEkuW1vgzEw_za AvQdUihIqI9JJGAibznpRFNpakun8ZWdQcxmHIijxXHBm0vayA s76VbT7czY5g6PoCn90DzIdM9ACsEZj5fInEf8QhN_DNTJxc_Q GVKMUVN9a893SaNXBcbnNFex7HXC9VHUO47OV_PCdIBseXJo4l Gzi2HyntL5gjlhODTZSdvZRilsW9DBb9jX0jRpaT80Qe4rEMkp 3ULUzbOpBvPTDJLRyPv3UnBDsZ8P9AerqZnfMBMjoD6NBCrIrt 8pljQU23Qu9vqUFjDMiIfkw1qPAHnvpMr1uSUws3NdnZgEMDbI 9kExpeKuwx0T2S4kGtKbjFhmGROSjpPkEO_Op9ZJHxYUihFuHZ WOd3rQ3ViqIKPWZidHMgYQyjthD1OWk48X4WaUMmXSwM6aJqTk Cwg6vqcy5-I_FJeuaNoz__zKqHLVZk_T4Ft2tJ6hLWt1MgIMVp64ipHBYPRa 43zWM9klgFb7tB0VUwNUq5Z2_uAcW4gaRhjVR93V=w1200-h900-no

[56Mark]

Amazing! Wish I had the tools and the skills. Do you have a youtube channel?

[MP&C]

Here:

https://www.youtube.com/channel/UCtRedgDFHDnLuBO040NdL1g

[56Mark]

Subscribed. Thanks

[Rustaddict]

Yes thanks for the link.