Just joined? Please introduce yourself.

Search:

Type: Posts; User: Rustaddict

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    179
    Views
    50,589

    Have you stopped building frames permanately ?

    Have you stopped building frames permanately ?
  2. Replies
    608
    Views
    168,796

    Does this site give you the ability to delete...

    Does this site give you the ability to delete unwanted posts out of your thread?
  3. Replies
    608
    Views
    168,796

    C-Nut, I rarely post but I'm enjoying watching...

    C-Nut, I rarely post but I'm enjoying watching your car come together and the detail you show. It's turning out to be super nice.
  4. Replies
    5
    Views
    2,844

    yes, the R is for resistor.

    yes, the R is for resistor.
  5. how did you blow your original rear end ?

    how did you blow your original rear end ?
  6. Replies
    3
    Views
    2,380

    Just shooting off the hip, are you sure your...

    Just shooting off the hip, are you sure your timing is right? Have you tried advancing it a little more to see if theres an improvement?
  7. Replies
    18
    Views
    5,358

    I second that.

    I second that.
  8. Replies
    1,013
    Views
    435,842

    Sticky: Robert, Are you making your door panels out of...

    Robert, Are you making your door panels out of sheet metal ?
  9. Replies
    32
    Views
    15,501

    That is a good looking car. You've got something...

    That is a good looking car. You've got something there to be proud of
  10. Replies
    9
    Views
    4,712

    I have no experience with either.

    I have no experience with either.
  11. Replies
    9
    Views
    4,712

    To the best of my knowledge, no one is making a 9...

    To the best of my knowledge, no one is making a 9 passenger fuel tank. You'll have to repair what you have. If I were using the 97 vortec and auto trans, I'd put an intake manifold & carburetor on it...
  12. Replies
    8
    Views
    4,429

    yes the water pump turns backwards on factory set...

    yes the water pump turns backwards on factory set ups. Not sure about aftermarket set ups.

    I always believed that ideally the fan shroud dictated how far from the radiator the fan should be. I...
  13. Replies
    8
    Views
    4,429

    Is it a used GM or aftermarket serpentine set up ?

    Is it a used GM or aftermarket serpentine set up ?
  14. Replies
    61
    Views
    16,591

    I dont think having a 57 linkage has anything to...

    I dont think having a 57 linkage has anything to do with the oil filter clearance. The benefit of the 57 stuff is it is a better design than the first 2 years. You need a 57 Z bar if you get 57 lower...
  15. Replies
    33
    Views
    16,047

    You're welcome. I was just kidding I know a few...

    You're welcome. I was just kidding I know a few people. One thing I will add is I had to take a die and cut the threads a little farther down the shaft and shorten the threaded end of the rod a...
  16. Replies
    33
    Views
    16,047

    I dont have any friends. I was doing the best I...

    I dont have any friends. I was doing the best I could with what I have to work with.
  17. Replies
    33
    Views
    16,047

    The throttle is wide open. I was by myself and...

    The throttle is wide open. I was by myself and checking for wide open throttle when I floored the gas and since I could'nt be at the carb and on the gas pedal at the same time, I leaned out of the...
  18. Replies
    33
    Views
    16,047

    For comparison's sake heres mine. I have the east...

    For comparison's sake heres mine. I have the east coast chevy rod. 11673
  19. Replies
    4
    Views
    1,994

    Could you open the hole up a little bit and go...

    Could you open the hole up a little bit and go with the 7/16 bolt ?
  20. Replies
    33
    Views
    16,047

    East Coast Chevy ( and others ) sell the correct...

    East Coast Chevy ( and others ) sell the correct rod that goes from the firewall rod to the carb. I'm using that replacement rod on a Holley with no trouble.
  21. We used to have a place local that taught...

    We used to have a place local that taught disadvantaged people trades and they did sandblasting fairly cheap. Maybe you could spot blast the rust and scuff the rest. I live on the east coast and salt...
  22. Replies
    61
    Views
    16,591

    The thing is, the clearance is so tight between...

    The thing is, the clearance is so tight between the floor and the bench seat that it dosent really leave much room for the modifications you'd need to do. If your money is tight, it is possible to...
  23. Replies
    18
    Views
    5,358

    Sweet. How much do you know about it?

    Sweet. How much do you know about it?
  24. I have use both over self etching primer and they...

    I have use both over self etching primer and they seemed to hold up well. This was before I knew epoxy primer existed and there's no doubt that Epoxy primer is the superior product to use these days....
  25. Replies
    61
    Views
    16,591

    Here's another suggestion to buy new 57 clutch...

    Here's another suggestion to buy new 57 clutch linkage and be done with it
Results 1 to 25 of 179
Page 1 of 8 1 2 3 4