Just joined? Please introduce yourself.
Classic Edge Designs, LLC Prime Custom Cars, LLC MadMooks

Search:

Type: Posts; User: scorpion1110

Page 1 of 14 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    10
    Views
    53

    Just pulled the whole factory power assist off my...

    Just pulled the whole factory power assist off my 55 Wagon; RAM, Valve, drag link, steering arm, special tie rod end, and a saginaw pump and the hoses. Also the frame bracket. Went to a CPP 500 box...
  2. Replies
    11
    Views
    469

    So issue solved. When I fed the light from an...

    So issue solved.

    When I fed the light from an ignition hot everything works as it should. So the feed that I was using was from the supplemental fuse block which has a tap to the main fuse flock....
  3. Replies
    11
    Views
    469

    The only possible thing I can think is that the...

    The only possible thing I can think is that the power feed to the indicators is not a switched feed. The fuel pump has one ground. The temp sender technically has two; the ground to the sender and...
  4. Replies
    11
    Views
    469

    Continued troubleshooting. When I remove the fan...

    Continued troubleshooting. When I remove the fan ground from the toggle, the light behaves as it should. Full dark at off. No impact from wiper switch or ignition. So its the fan circuit somehow....
  5. Replies
    11
    Views
    469

    Resurrecting this thread due to my slow trip into...

    Resurrecting this thread due to my slow trip into insanity on this switch panel.

    I ran a supplemntal + feed to each indicator light at one side.
    I ran the other side of the light to one side of...
  6. Replies
    11
    Views
    469

    CN- Huge help as always. The funny thing is I...

    CN-

    Huge help as always. The funny thing is I initially intended to run 12V to the light and the other side to the relay coil side of the toggle, which would have worked. So I would have gotten...
  7. Replies
    11
    Views
    469

    CN- I think I got this totally wrong. Heres...

    CN-

    I think I got this totally wrong.

    Heres is the schematic:

    10463

    And here is the sender:
  8. Replies
    11
    Views
    469

    The feed to the fan has a relay at the fuse block...

    The feed to the fan has a relay at the fuse block with power fed to the fan via 14 gauge wire and it uses a 25 amp fuse at the fuse block. It also is a 14 circuit harness.

    Its a single fan. ...
  9. Replies
    11
    Views
    469

    Thanks CN- I wired the SPAL Fans using the...

    Thanks CN-

    I wired the SPAL Fans using the stock Kwik Wire 12 circuit harness and then added a supplemental block to cover 3 more circuits. There is a fan relay incorporated into the fuse block...
  10. Replies
    11
    Views
    469

    Ground Side Toggle Switch

    Ok, I did the web research and cannot find a thing.

    I am running SPAL fans in my 55 Wagon. The ground goes to the temp sender and it also has a ground toggle in a supplemental switch panel...
  11. Replies
    10
    Views
    554

    Welcome. Your 55 has a nice stance.

    Welcome.

    Your 55 has a nice stance.
  12. Replies
    8
    Views
    391

    Welcome aboard! S

    Welcome aboard!

    S
  13. I figured it would probably end up looking a lot...

    I figured it would probably end up looking a lot better than the ends.. I thought there might be something out there in decent chrome that would make the bumper look about the same all the way...
  14. I will probably end there but thought Id give it...

    I will probably end there but thought Id give it a try. The chrome on the ends is good original chrome. My center section would be useable if someone hadnt drilled and then welded holes shut. I...
  15. Replies
    373
    Views
    38,334

    Its a good look. I can see from the pic how it...

    Its a good look. I can see from the pic how it works with the latch.

    I am sure the chroming wasnt cheap.
  16. Check Soffseal or Steele, but preferably...

    Check Soffseal or Steele, but preferably Soffseal. I just installed their tailgate seal and its very nice. The liftgate seal which I am pretty sure is Danchuk just wasnt real nice.

    S
  17. Replies
    7
    Views
    520

    Doug, I have read about intermittent leaking on...

    Doug, I have read about intermittent leaking on the CPP500 boxes. I have one I havent installed yet. How about your fittings? I think the box is inverted flair. I know CPP has the specs on their...
  18. Center Section 1955 Chevy Wagon Rear Bumper

    Anyone have a decent original chrome center section for a 55 Wagon? Its got the flat spot for the license plate.

    They make a new chrome repop but I have a decent set of original ends and dont...
  19. RD; My perspective and I do all my own body...

    RD;

    My perspective and I do all my own body work, except paint. I am equiped to shoot in my shop, but I havent laid color since the lacquer days.

    I just had a color match, and body finish and...
  20. I ended up installing the PW because the...

    I ended up installing the PW because the regulators were shot. I figured it was just as easy and about the same cost to install the PW.

    You guys have me comfortable on the non-relay wire, plus...
  21. Black exterior and red interior works every time....

    Black exterior and red interior works every time.

    I love black cars.
  22. Looks good RD It might make sense to have them...

    Looks good RD

    It might make sense to have them cut it in if you know your colors. My wagon was painted when I got it and I have had to do a lot of work including some fab and despite my best...
  23. CN, RD: Here is the SPW Schematic: 10407 ...

    CN, RD:

    Here is the SPW Schematic:

    10407

    Based on your thoughts, I am going to wire per their recommendation. The voltage drop wont have a measurable impact so the relays are probably not...
  24. CN, RD; So if I dont go with the relay set up,...

    CN, RD;

    So if I dont go with the relay set up, I just split the one 25 amp circuit and feed each side? SPW gave me a diagram to use, but I got sidetracked to the relay discussion.

    Sometimes you...
  25. Replies
    22
    Views
    2,018

    You are right RD. I have just enough energy to...

    You are right RD. I have just enough energy to work on my project. I have the endless supply of "friends" who always need my help, but never offer anything;like a few $$, replace shop supplies,...
Results 1 to 25 of 334
Page 1 of 14 1 2 3 4