Just joined? Please introduce yourself.
Results 1 to 5 of 5

Thread: Any spot weld drill bit recommendations?

  1. #1
    Registered Member Bihili's Avatar
    Join Date
    Sep 2012

    Member #:896
    Location
    outside K. C.
    Posts
    267

    Any spot weld drill bit recommendations?

    This next project requires removing all floors and rockers. So I need a premium spot weld drill bit. Got any suggestions
    Bill 1957-427-177-6-410

  2. #2
    Registered Member chevynut's Avatar
    Join Date
    Nov 2011

    Member #:115
    Location
    Fort Collins, CO
    Posts
    10,835
    What are you working on now Bill? If I don't plan to save a panel, I just use a die grinder with a 3" disc.
    56 Nomad, Ramjet 502, Viper 6-speed T56, C4 Corvette front and rear suspension


    Other vehicles:

    56 Chevy 2-door BelAir sedan
    56 Chevy 210 4-door sedan
    57 Chevy 210 4-door sedan
    1962 327/340HP Corvette
    1961 Willys CJ3B Jeep
    2001 Porsche Boxster S
    2003 Chevy Silverado 2500 HD Duramax
    2019 GMC Sierra Denali Duramax

  3. #3
    Registered Member
    Join Date
    Apr 2012

    Member #:571
    Posts
    4,671
    If you're trying to save the panel(s), I use a Wivco spot weld cutter. It has a 1/8" centering drill, and you can use a standard 1/8" drill bit when the original wears out. The cutter itself is like a 2 flute end mill. It can be sharpened using a belt sander. Blair makes a similar bit that is probably more popular.

    The Wivco bit makes pretty quick work of a spot weld. I also think it rivals the 3" disc for speed, and it's not nearly as messy and sloppy.

    Definitely much better than the "mini hole saw" cutters.

  4. #4
    Registered Member Bihili's Avatar
    Join Date
    Sep 2012

    Member #:896
    Location
    outside K. C.
    Posts
    267
    Rick, I have a Wivco spot weld cutter with 1/8" centering drill bit that I broke and wanted to try a different style.
    Since I am not saving any of the old metal I will try the die grinder.
    In a few days after I get everything inventoried I will show you my next project.
    Bill 1957-427-177-6-410

  5. #5
    Registered Member MP&C's Avatar
    Join Date
    Dec 2013

    Member #:2017
    Location
    Southern MD
    Posts
    1,290
    Bill, here's my take on the good and bad with the various methods of spot weld removal....


    What you use will largely be determined by which panel you are saving, what access you have to either side, and how well you and the tool work in harmony.
    If you are facing the piece you wish to save, and the lower panel is essentially a throwaway, then simply use a drill bit the same size you would select for plug welds, and drill out the spot weld. When you place the new panel beneath and clamp it up, the hole you drilled in the top panel now serves as your plug weld hole.
    If you are saving the lower panel, and throwing away the top, you can use whatever works best for you. There are many ways to accomplish the same thing, but if you are not proficient in using one method, try another. I think each method has it's faults, so pick the one that best suits the area you are working.


    The holesaw type cutter typically cuts like any other holesaw does, and once the teeth start to cut a "channel", it is difficult to see how far along you are progressing. At the point the cutter reaches the second layer, which is where you would want to stop, if there were a bit of rust between the two panels and your cutter had enough speed, you would have a visual indicator in a wisp of "rust smoke" that is seen coming around the cutter. It is here that, even though some moderate speed is needed to produce this indicator, light pressure is also needed (better classified as "restraint") so that you don't go through too far and damage the second panel. In my case, I found myself going through too far, and would either need to repair the deep channel I just cut in the second layer, or would have to weld in a circle to repair the gaping hole I just left. Needless to say, I no longer use this method, and gave the cutter I did have to someone else that hopefully is having better luck with it than I did.


    Some of the cutters have a spring loaded center punch, much like a machinists roto-bore. Even with an intial center punch used in the middle of the spot weld, These cutters have the misfortune of slipping off center, and many people will simply drill a 1/8" diameter hole, either partially or all the way thru, to prevent the cutter from walking about. I'll stop here and offer a generalized thought. If you have difficulty filling an 1/8" hole in a piece of sheet metal with your welder, you will likely have problems with the pilot drill method, and perhaps should try one of the other methods.
    I think the Wivco cutters will work better than the hole saw type, in that they mimick an end mill, so the cutter is relatively flat on the bottom. This should give a less aggressive cut, a plus for people like me who may have a problem of leaning too hard on the cutter. The open flute design will also allow you to better see what is going on than the holesaw type, which obscures everything. It does use the pilot bit, so if that is not an issue (see above paragraph), then this is a good choice.



    The blair cutter is available in either the spring loaded version or the pilot bit version, I think these are likely a more aggresive cut than the wivco, especially since the cutting surface is extremely narrow, so it may be more likely to pose the cut through problems I described initially.



    The rounded burr grinder is also a good method which should somewhat limit the damage to the (throwaway) panel to just slightly larger than that of a spot weld cutter. The downside is that these also come with little tiny slivers of metal that are a pain when you get them in your skin, so it would be advantageous to address these with a vacuum cleaner/foxtail and dust pan on occasion to keep the issue at bay. A pair of work gloves come in handy as well. Keep some duct tape handy to pull out the slivers that sneak by.





    The last method I'll discuss is the one that I use because I don't play nice with the holesaw type. I use a 3" cutoff wheel with a 1/16" thick cutoff disc and use the tool to grind away the spot weld. I find for myself, it offers a less obstructed view of any of the methods listed, and with the proper speed (fast), will give you an indicator in the discoloration of the top layer (blue or darkened) usually before you have even broken into the second layer. Basically the metal is heating up and as it starts to get thin, it heats up more quickly and shows this via a color change. The color change back to bright silver will indicate you have reached the second layer, and act as a guide where to not grind anymore (the bright area) and where to grind, the blue/dark circle surround it. The disadvantages with this method, are the top panel is basically useless now; you will need good eye protection (moreso than the holesaw type cutters), and due to the grinding particulate, will need to use a respirator/mask to prevent you from hocking up black globs shortly afterward. I usually get a 3M or equivalent paint respirator, as the typical dust masks only serve to fog up your safety glasses, and as is evident upon the removal of the dust mask by the residue alongside the bridge of your nose, they don't work all that well. A paint style respirator exhales to the sides, away from your safety glasses, and typically conforms to your face much better.
    Grind pattern visible:



    Now as discussed at the beginning, had we wanted to save the flange and the rear panel was a throwaway, you could simply drill through the spot weld, and the resulting hole in the top panel would serve as a plug weld hole for re-attaching to the new rear panel.

    That should give a brief view of both the good and the bad with each method, I feel it's up to each individual to figure out which one works best for them and best for the situation at hand.
    Robert



    MP&C Shop Projects-Metalshaping Tutorials


    Instagram @ mccartney_paint_and_custom


    .

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •