Just joined? Please introduce yourself.
Results 1 to 8 of 8

Thread: Body to Frame Bolts

  1. #1
    Administrator 567chevys's Avatar
    Join Date
    Oct 2010

    Member #:3
    Location
    Woodland Washington
    Posts
    2,413

    Body to Frame Bolts

    I have a question,


    Why on a 1955 Chevy do they used 3/8-16 hex Bolts to hold the body on the frame ? When the Rubbers and sleeves are like 3/4" ID .


    Thanks Sid

    1955 2 DR Post
    1937 Chevy Coupe
    2023 Ford Super Duty F350 TREMOR
    2019 Corvette Z06
    1955 Chevy Nomad
    1935 Ford 2dr Slant back I have 4

  2. #2
    Registered Member
    Join Date
    Apr 2012

    Member #:571
    Posts
    4,671
    So you can move the body on the frame that small amount and still have the bolts go through the holes. Also this allows some of the mounts to be off in location.

  3. #3
    Registered Member
    Join Date
    Aug 2013

    Member #:1806
    Posts
    414
    Get the body as square as you can on the frame before you bolt it down, and watch the bolt torque, so you don't crush the rubber mounts.

  4. #4
    Registered Member NickP's Avatar
    Join Date
    Mar 2012

    Member #:1653
    Location
    De Queen, AR
    Posts
    4,157
    Hard to crush it to far with stock units. There is a tube washer assembly with OEM stuff. Even the Poly kits have a tube and washer setup that limits the compression.

  5. #5
    Registered Member
    Join Date
    Apr 2012

    Member #:571
    Posts
    4,671
    Still, the recommended torque is a bit less than what you'd expect for the bolt size. There is some compression of the rubber.

  6. #6
    Registered Member
    Join Date
    Nov 2015

    Member #:2764
    Posts
    649
    I don't recall the torque my instructions had, but it sure compressed the rubber a lot! Probably all bottomed out on the spacer insert (I think it had them?). I do remember that the difference in ride and handling was great. One of the improvements that ranks up there with a stiff front sway bar.

  7. #7
    Registered Member
    Join Date
    Apr 2012

    Member #:571
    Posts
    4,671
    My recollection is that the torque is 25 foot pounds, where a standard bolt that size would call for 30-35 foot pounds.

  8. #8
    Registered Member chevynut's Avatar
    Join Date
    Nov 2011

    Member #:115
    Location
    Fort Collins, CO
    Posts
    10,835
    The rubber is compressed some, but tightening it past the point where the washer is bottomed out on the sleeve doesn't compress it anymore. I think the reason they don't go to 35 ft-lb is that the bolt head and/or lockwasher would dent the washer too much. I've seen washers that had big dents in them. 25 ft-lb probably prevents that from happening, but still crushes the rubber completely.
    56 Nomad, Ramjet 502, Viper 6-speed T56, C4 Corvette front and rear suspension


    Other vehicles:

    56 Chevy 2-door BelAir sedan
    56 Chevy 210 4-door sedan
    57 Chevy 210 4-door sedan
    1962 327/340HP Corvette
    1961 Willys CJ3B Jeep
    2001 Porsche Boxster S
    2003 Chevy Silverado 2500 HD Duramax
    2019 GMC Sierra Denali Duramax

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •