Just joined? Please introduce yourself.
Results 1 to 5 of 5

Thread: Removing body from frame

  1. #1
    Registered Member
    Join Date
    Mar 2017

    Member #:3360
    Location
    Canton,Ohio
    Posts
    260

    Removing body from frame

    I need some advice on removing the body from the frame. I have a 2dr sedan 56, I'm going to be replacing the complete floor so I want to remove the doors before I remove the body to make it lighter, some say I don't have to brace the body because of the post and other's say you should always cross brace the body when you remove the doors. I look at previous posts but didn't find any thing. Pictures or drawings would help Thanks

  2. #2
    Registered Member
    Join Date
    Apr 2012

    Member #:571
    Posts
    4,671
    A solid 2 door sedan body does not need bracing. But since you are removing the floor, I would brace between the B pillars to keep the rocker panel area in the correct orientation. I would align the doors the best I could before removing them. Don't get too carried away with the bracing, you might need access to the rear passenger area to at least do some tack welding. Finish welding can be done after the braces are removed. Also do your floor fitting etc. using the frame as a jig, using new body mounts.

  3. #3
    Registered Member chevynut's Avatar
    Join Date
    Nov 2011

    Member #:115
    Location
    Fort Collins, CO
    Posts
    10,835
    I didn't use any bracing when replacing the floors in my Nomad and it turned out good. A Nomad body is similar to a sedan. I used floor halves and all new braces because that's all you could get at the time, except for a $2700 welded 2-piece floor from Sherman.

    I'm not sure I'd worry about aligning doors if you're going to remove them because the body is going to flex and they will have to be re-aligned when installed. If you leave them on to do the floor, then it makes sense to align them so you can tell if the body has moved at all. With a full welded floor the floor width is pre-determined so the rockers will need to be set at that width against the floor flanges.

    I sure wish they'd had full 1-piece floors with braces and inner rockers when I did mine.
    56 Nomad, Ramjet 502, Viper 6-speed T56, C4 Corvette front and rear suspension


    Other vehicles:

    56 Chevy 2-door BelAir sedan
    56 Chevy 210 4-door sedan
    57 Chevy 210 4-door sedan
    1962 327/340HP Corvette
    1961 Willys CJ3B Jeep
    2001 Porsche Boxster S
    2003 Chevy Silverado 2500 HD Duramax
    2019 GMC Sierra Denali Duramax

  4. #4
    Registered Member chasracer's Avatar
    Join Date
    Mar 2018

    Member #:3718
    Location
    Montpelier
    Posts
    230
    I worked on a '57 version years ago, the body was normal east coast stuff with some rocker and floor damage. Doors operated okay, don't think things were moving around. We put two lengths of 1/2" conduit across the door openings. Could have x'd them I guess but we just ran them parallel a few inches from the floor and just where the dash cleared at the top. We also put one length between posts about mid-way up the back of the seat. None of the glass cracked which is what we were more concerned about.

  5. #5
    Registered Member
    Join Date
    Mar 2017

    Member #:3360
    Location
    Canton,Ohio
    Posts
    260
    Thanks guy's, I'm going to have to change the outside rocker's also. Just so I 'm on the same page the B piller is the post correct?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •