View Full Version : SHEET metal INFO Needed
spike10
07-19-2013, 04:31 PM
I need a tail pan for a sedan delivey 57
I found
http://www.popscarparts.com/servlet/Cart?smode=update
http://www.shop.newclassicchevy.com/1955-57-Chevy-Station-Wagon-Sedan-Delivery-Nomad-Tailpan-TP13-553.htm
http://www.ebay.com/itm/Chevy-Nomad-and-Station-Wagon-Tail-Panel-Support-55-56-57-1955-1956-1957/151059693805?rt=nc&_trksid=p2047675.m1851&_trkparms=aid%3D222002%26algo%3DSIC.FIT%26ao%3D1%2 6asc%3D261%26meid%3D9164921815788941728%26pid%3D10 0005%26prg%3D1088%26rk%3D1%26rkt%3D5%26sd%3D161041 369992%26
http://shop.oldedaysclassiccarparts.com/NOMAD-AND-WAGON-ITEMS_c24.htm
Seems I can get the panel for just under $100 and supports for about $35
Does anyone have any experience with either of these sheet metal guys ?
or know a better one ??
I hate to buy the same stuff twice ......
thanks
I am almost done
Spike
chevynut
07-20-2013, 07:26 AM
Most of these parts are made by one or two manufacturers, and sold by several dealers. So they're the same parts. The bare metal parts are made by Sherman and the black EDP parts are made in Taiwan by Golden Star. Some people say the Taiwan parts actually fit better. The Taiwan parts are also sold through Resto-World who typically has some good prices.
I would buy them where you can get both parts from the same place at the best price with shipping included.
http://www.parts123.com/parts123/yb.dll?parta~dyndetail~Z5Z5Z50000080i~Z5Z5Z500920~ P105.00~~~~S3U40M5DAL20873289050B~Z5Z5Z5~Z5Z5Z5000 0080i
http://www.parts123.com/parts123/yb.dll?parta~dyndetail~Z5Z5Z50000080i~Z5Z5Z5AAFQD~ P350.00~~~~S3U40M5DAL20873289050B~Z5Z5Z5~Z5Z5Z5000 0080i
http://www.parts123.com/parts123/yb.dll?parta~dyndetail~Z5Z5Z50000080i~Z5Z5Z5AAFQC~ P29.00~~~~S3U40M5DAL20873289050B~Z5Z5Z5~Z5Z5Z50000 080i
We installed the bare steel one from Sherman/CarsInc and found the lower crease in the wrong place..... somewhat easily fixed though:
We had trimmed the pinch weld flanges off the tailpan and adjacent quarter, leaving a bit extra to insure we had enough metal to span the gap for butt welding... This was to eliminate the rust/dirt trap that the pinch weld flanges always seem to be...
http://i5.photobucket.com/albums/y167/rmccartney/1955%20Chevy%20Wagon%20Restoration%20Album%203/Picture288.jpg
Used the tipping tool to unfold the remainder of the flange and the door skin hammer to flatten it out...
http://i5.photobucket.com/albums/y167/rmccartney/1955%20Chevy%20Wagon%20Restoration%20Album%203/Picture289.jpg
http://i5.photobucket.com/albums/y167/rmccartney/1955%20Chevy%20Wagon%20Restoration%20Album%203/Picture290.jpg
After another test fit, the reproduction showed to be not that accurate, go figure....
http://i5.photobucket.com/albums/y167/rmccartney/1955%20Chevy%20Wagon%20Restoration%20Album%203/Picture296.jpg
After marking the new bend location, the bead roller was fitted with the tipping die to relocate the bend...
http://i5.photobucket.com/albums/y167/rmccartney/1955%20Chevy%20Wagon%20Restoration%20Album%203/Picture301.jpg
Along with making the new bend, the tipping die leaves a "crease" indicator on the bottom side. This is then aligned to the edge of the anvil, and a hammer is then used to flatten out the incorrect crease...
http://i5.photobucket.com/albums/y167/rmccartney/1955%20Chevy%20Wagon%20Restoration%20Album%203/Picture303.jpg
http://i5.photobucket.com/albums/y167/rmccartney/1955%20Chevy%20Wagon%20Restoration%20Album%203/Picture304.jpg
For a much better fit.....
http://i5.photobucket.com/albums/y167/rmccartney/1955%20Chevy%20Wagon%20Restoration%20Album%203/Picture307.jpg
http://i5.photobucket.com/albums/y167/rmccartney/1955%20Chevy%20Wagon%20Restoration%20Album%203/Picture308.jpg
Rick_L
12-11-2013, 07:31 PM
I'm not so sure that the alternative won't need similar mods - just that the exact details will be different.
DoubleNickle
12-20-2013, 01:53 PM
Robert, you do very nice work! :) Wish I had your talent.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.