View Profile: timo pajala - TriFiveChevys - Trifivechevys.com is an online car club for enthusiasts of Trifive Chevy Cars and Trucks.

Today, 10:27 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Thank you very much for kind words! They give me good boost for building the car :) i made front shock mounts today and gonna post video when...

62 replies | 3481 view(s)

Yesterday, 08:29 PM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Its really close To been parallel. I measured it with using cross laser

62 replies | 3481 view(s)

Yesterday, 11:15 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

4 link and rear bags are tacked In.

62 replies | 3481 view(s)

01-15-2021, 10:46 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

It stated that it should be above axle center line so im gonna lift the bracket about an inch or so

62 replies | 3481 view(s)

01-15-2021, 05:56 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Im little bit strugling with the 4 link upper bracket, do they need to be on the top of belhousing or does the centerline of axle be enough? I tacked...

62 replies | 3481 view(s)

01-15-2021, 12:19 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Those can be frustrating things to do when the car is build. I hope to mock everything before buiding final time

62 replies | 3481 view(s)

01-14-2021, 02:08 PM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Today i mocked the 4link and welded rear for body install before finall weld process. Just want to make sure that Front wheels turn ok etc. I dont...

62 replies | 3481 view(s)

01-13-2021, 07:10 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

No undercoating so quite easy Job To grind Off. About 4h or so for the half of the floor. I cleaned the other half earlier. I installed the Front...

62 replies | 3481 view(s)

01-12-2021, 06:54 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Today

62 replies | 3481 view(s)

01-11-2021, 12:13 PM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Thats the really good part! I welded the old molding holes shut. Tomorrow perhaps do the Seat bracket.

62 replies | 3481 view(s)

01-10-2021, 11:32 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Thank you very much! Im not good at keeping cars stock :p

62 replies | 3481 view(s)

01-10-2021, 08:12 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

I have painted the front End. Epokxy is first and paint after that. Today I reassembled the front control arms with New Ball Joints and also...

62 replies | 3481 view(s)

01-07-2021, 10:07 AM

timo pajala replied to a thread Molding holes dont match in TrifiveChevy Stock Discussion

I did not realise then that the holes were so much different but thats not a big deal. Little more work:grin:

7 replies | 280 view(s)

01-06-2021, 11:10 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Holes are too low in the door. About half inch in the back and over inch in the front

62 replies | 3481 view(s)

01-06-2021, 09:09 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Little setback here, door molding holes are way Off and have To weld the shut and make New ones!

62 replies | 3481 view(s)

01-06-2021, 09:08 AM

timo pajala replied to a thread Molding holes dont match in TrifiveChevy Stock Discussion

I put the fenders on today and the holes are way Off compared to the door so I have To weld the door holes shut and make New holes for the molding...

7 replies | 280 view(s)

01-06-2021, 12:16 AM

timo pajala replied to a thread Molding holes dont match in TrifiveChevy Stock Discussion

I was wondering the same. Whats the difference in these Doors?

7 replies | 280 view(s)

01-05-2021, 01:47 PM

timo pajala started a thread Molding holes dont match in TrifiveChevy Stock Discussion

7 replies | 280 view(s)

01-02-2021, 11:17 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Panel gaps

62 replies | 3481 view(s)

12-30-2020, 01:07 PM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Patch work passenger door

62 replies | 3481 view(s)

12-30-2020, 01:06 PM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Thank you very much :)

62 replies | 3481 view(s)

12-28-2020, 07:50 AM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Thank you and it sure was!

62 replies | 3481 view(s)

12-27-2020, 12:49 PM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

Car has been sanded and garace cleaned once

62 replies | 3481 view(s)

12-21-2020, 09:21 PM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

This car was a great starting point! Door skin is the only thing a have To change what comes to sheetmetal work 👍🏻 Today im gonna finish the...

62 replies | 3481 view(s)

12-21-2020, 12:02 PM

timo pajala replied to a thread 1957 2d post starting soon in Member Project Updates

I have sanded the whole car and few issues came up. Few dings on the roof and on the door. Few patches have To do to the door and lend a dent puller...

62 replies | 3481 view(s)

timo pajala
Registered Member

Mini Statistics

Recent Visitors

Basic Information

Statistics

Total Posts

General Information

timo pajala Registered Member

Mini Statistics

Recent Visitors

Basic Information

Statistics

Total Posts

General Information

timo pajala
Registered Member