View Profile: ykf7b0 - TriFiveChevys - Trifivechevys.com is an online car club for enthusiasts of Trifive Chevy Cars and Trucks.

01-17-2021, 04:45 PM

ykf7b0 replied to a thread battery disconnect switch in TrifiveChevy Electrical Discussion

I bought my disconnect at Wal Mart. Cheap but effective!

5 replies | 108 view(s)

01-12-2021, 04:54 PM

ykf7b0 replied to a thread Long Water Pump with Clutch Fan in TrifiveChevy Cooling Systems

I have went with a Hayden 2747 fan clutch, Derale 17117 6 blade fan, and an Ecklers 18-307 aluminun fan shroud. By my measurements I should be about...

7 replies | 183 view(s)

01-11-2021, 06:18 PM

ykf7b0 replied to a thread Long Water Pump with Clutch Fan in TrifiveChevy Cooling Systems

Another question if I may?. How far from your radiators are your fans no matter what water pumps you are using?

7 replies | 183 view(s)

01-11-2021, 02:44 PM

ykf7b0 replied to a thread Long Water Pump with Clutch Fan in TrifiveChevy Cooling Systems

Serpentine pulley set up is requiring a long pump and that’s what’s on it already.

7 replies | 183 view(s)

01-11-2021, 01:03 PM

ykf7b0 started a thread Long Water Pump with Clutch Fan in TrifiveChevy Cooling Systems

Are any of you using a clutch fan setup with a long water pump in a small block 55? If so, what setup do you have please? Bo

7 replies | 183 view(s)

01-10-2021, 07:10 AM

ykf7b0 replied to a thread 55 Auto to Manual Conversion in TrifiveChevy DriveLine, Powertrain, and Transmission

Thanks Rick!

40 replies | 1208 view(s)

01-08-2021, 02:06 PM

ykf7b0 replied to a thread 55 Auto to Manual Conversion in TrifiveChevy DriveLine, Powertrain, and Transmission

Here is where I’m a little confused. Can I use a 57 clutch fork and lower rod with a 55 z-bar or not? Thanks!

40 replies | 1208 view(s)

01-08-2021, 11:23 AM

ykf7b0 replied to a thread 55 Auto to Manual Conversion in TrifiveChevy DriveLine, Powertrain, and Transmission

Ok, which is better? Get 55 parts and not modify with bushings or change pivot or go with 57 parts and make necessary changes? Thanks?

40 replies | 1208 view(s)

01-08-2021, 10:38 AM

ykf7b0 replied to a thread 55 Auto to Manual Conversion in TrifiveChevy DriveLine, Powertrain, and Transmission

That sounds easier.

40 replies | 1208 view(s)

01-08-2021, 10:30 AM

ykf7b0 replied to a thread 55 Auto to Manual Conversion in TrifiveChevy DriveLine, Powertrain, and Transmission

I have no idea what is stock so to be safe would you recommend 57 parts? Also, what do I do about the bushing and pivot ball? Thanks?

40 replies | 1208 view(s)

01-07-2021, 09:21 PM

ykf7b0 replied to a thread 55 Auto to Manual Conversion in TrifiveChevy DriveLine, Powertrain, and Transmission

Ok, So I need a 57 clutch linkage to clear the oil filter on my 1975 350 engine but I need to either make a bushing for my 1955 5/8 shaft for better...

40 replies | 1208 view(s)

01-04-2021, 09:14 PM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

Thanks for the picture of the rod and the lead on where to get one for myself my Friend!!!

33 replies | 1376 view(s)

01-03-2021, 09:36 AM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

It does look cleaner though.

33 replies | 1376 view(s)

01-03-2021, 08:02 AM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

Seems logical.

33 replies | 1376 view(s)

01-03-2021, 05:33 AM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

Oh ok Thanks! I saw the throttle on Rustsaddicts car too and I was thinking the same thing except I don't think the firewall lever is in idle...

33 replies | 1376 view(s)

01-02-2021, 07:36 PM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

I went on Don's East Coast site and haven't been able to find that rod so would you have a part number? I definitely like the spring position better....

33 replies | 1376 view(s)

01-02-2021, 02:17 PM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

I'm not sure of which hole on the carburetor arm the linkage is supposed to be attached but the 1/4 rod fit better in the hole I'm using. I have...

33 replies | 1376 view(s)

01-02-2021, 12:53 PM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

I have settled on this for a while and it seems to be fine for the time being. Thanks to all who have chimed in! I feel like I have captured the...

33 replies | 1376 view(s)

01-01-2021, 07:06 PM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

With the Dog on this one, Check this out from Speedway just one of many things they offer. Part # 721BJGR4 $1.99 Thanks markm, but why...

33 replies | 1376 view(s)

01-01-2021, 06:51 PM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

I bought a set up from Eckler's but I was thinking it must have been for a 1955 Rochester because it didn't correlate to my Holley but I could be...

33 replies | 1376 view(s)

01-01-2021, 06:45 PM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

I don't understand? I will be using a return spring. ???

33 replies | 1376 view(s)

01-01-2021, 02:38 PM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

After a trip to Tractor Supply this is what I came up with. I had to drill and tap the union for the carburetor attachment.

33 replies | 1376 view(s)

01-01-2021, 06:20 AM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

Dave, if you are using a Holley 4 barrel, how is the rod attached to the carb? Thanks! Bo

33 replies | 1376 view(s)

12-31-2020, 10:32 PM

ykf7b0 replied to a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

What I have is a mess. 1/4 x 20 threaded rod that is bent into an L shape on the accelerator arm end, on the carburetor end there is a piece...

33 replies | 1376 view(s)

12-31-2020, 12:17 PM

ykf7b0 started a thread Throttle Linkage in TrifiveChevy Fuel systems; Fuel Injection and/or ECM /PCM

My newly acquired 55 has a Holley 700 cfm carb and rigged up throttle assembly. I know I could get a Lokar set up but I'm curious as to what you...

33 replies | 1376 view(s)

12-31-2020, 05:55 AM

ykf7b0 replied to a thread Bench Seat Backrest in TrifiveChevy Interiors Discussion

Thank you busterwivell!!!

3 replies | 268 view(s)

12-30-2020, 08:43 PM

ykf7b0 replied to a thread Bench Seat Backrest in TrifiveChevy Interiors Discussion

Disregard my previous post please. They are back seat stops and I have found them.

3 replies | 268 view(s)

12-30-2020, 07:55 PM

ykf7b0 started a thread Bench Seat Backrest in TrifiveChevy Interiors Discussion

Could someone tell what those black rubber pieces that the bench seat backrest sit on are called? Each are attached by a single screw and I have...

3 replies | 268 view(s)

12-29-2020, 03:13 PM

ykf7b0 replied to a thread 55 Auto to Manual Conversion in TrifiveChevy DriveLine, Powertrain, and Transmission

I have the yoke. 3 rings and it should be 2.64 first gear correct?

40 replies | 1208 view(s)

12-29-2020, 10:59 AM

ykf7b0 replied to a thread 55 Auto to Manual Conversion in TrifiveChevy DriveLine, Powertrain, and Transmission

From what I can gather, that little difference can matter a whole lot regarding the seat position. I don’t know. ?

40 replies | 1208 view(s)

ykf7b0
Registered Member

Mini Statistics

Recent Visitors

2 Visitor Messages

Basic Information

About ykf7b0

Signature

Statistics

Total Posts

Visitor Messages

General Information

ykf7b0 Registered Member

Mini Statistics

Recent Visitors

2 Visitor Messages

Basic Information

About ykf7b0

Signature

Statistics

Total Posts

Visitor Messages

General Information

ykf7b0
Registered Member