-
The more I looked at our panel with the spot weld carnage, the more I disliked the result, so with new linear guides installed, we made all new today using stainless pop rivets to hold the guides in place. This will leave a few 1/8" holes to fill, but should be much less issue than cleaning up after the spot welds...
We needed just a bit more throat for this set of "lengthened" hood sides, so one bolt was removed from the material clamp and then rotated the clamp inward 90". This lets the panel pass through rather than bottom out in the clamp.
http://i5.photobucket.com/albums/y16...ure%203686.jpg
Guides riveted in place....
http://i5.photobucket.com/albums/y16...ure%203687.jpg
http://i5.photobucket.com/albums/y16...ure%203688.jpg
http://i5.photobucket.com/albums/y16...ure%203689.jpg
Here's the new version 1, much cleaner, less distortion, and we can re-use the guides...
http://i5.photobucket.com/albums/y16...ure%203694.jpg
http://i5.photobucket.com/albums/y16...ure%203695.jpg
http://i5.photobucket.com/albums/y16...ure%203696.jpg
The cowl piece was done without guides....
http://i5.photobucket.com/albums/y16...ure%203700.jpg
And version 2 with the cowl piece.....
http://i5.photobucket.com/albums/y16...ure%203699.jpg
Dave (the car owner) stopped by this afternoon and picked up the samples, and indicated he was being over-ruled by most parties on louvers in the cowl, so likely that version won't be used...
-
Now, in the interest of showing the good with the bad, the lessons learned if you will, Safety tip of the day is to deburr your sheet metal even if it's only for practice pieces....
http://i5.photobucket.com/albums/y16...ure%203685.jpg
-
Consider that as "paying the tax man" for all the great work you do Robert. :(
-
So far so good, nothing turning green... :p
Tonight we worked on the frame, used some poster board to make a pattern for a strengthening plate to span the pocket kit on each frame rail..
http://i5.photobucket.com/albums/y16...ure%203705.jpg
While Kyle filled in some frame holes by plug welding to the pocket kit, I cut out the frame plates...
http://i5.photobucket.com/albums/y16...ure%203706.jpg
http://i5.photobucket.com/albums/y16...ure%203708.jpg
http://i5.photobucket.com/albums/y16...ure%203709.jpg
http://i5.photobucket.com/albums/y16...ure%203710.jpg
And the shop vacuum is about on it's last leg, it leaves behind about as much as it picks up. For anyone at DYSON or SHARK vacuum that would like to send a test sample, we can sure do a stress analysis on your product.. :lol:
-
-
Still working on the frame, Kyle was prepping the frame for welding on the strengthening plates while I drilled the plates for plug welds..
Plug welding....
http://i5.photobucket.com/albums/y16...ure%203733.jpg
http://i5.photobucket.com/albums/y16...ure%203735.jpg
http://i5.photobucket.com/albums/y16...ure%203737.jpg
The outer perimeter will be Tig welded...
-
Still working the frame, here's the driver's side plate all clamped up and ready to go.. Hindsight and all that, should have made the plates about 2" longer and we wouldn't have those pesky holes in the way at the front end..
http://i5.photobucket.com/albums/y16...ure%203739.jpg
So we decided to cut out some 14 gauge and fill in those holes. Cut a piece the same width as the hole, and rounded the end. Then used the band saw to cut a vee on the back side of the "plugs" and continued to clean up the radius with the 3" Roloc sander. Once close, a bit more on the band saw and break off the remaining, then fine tune with the sander..
http://i5.photobucket.com/albums/y16...ure%203741.jpg
http://i5.photobucket.com/albums/y16...ure%203743.jpg
Magnet used to hold in place for tacking..
http://i5.photobucket.com/albums/y16...ure%203748.jpg
http://i5.photobucket.com/albums/y16...ure%203742.jpg
For TIG welding the perimeter of the plates, we decided to make up a "crutch" that we could rest our hand on for better holding the torch...
http://i5.photobucket.com/albums/y16...ure%203751.jpg
http://i5.photobucket.com/albums/y16...ure%203750.jpg
Kyle is getting a pretty good hold on this welding stuff...
http://i5.photobucket.com/albums/y16...ure%203747.jpg
He even let me get in some practice....
http://i5.photobucket.com/albums/y16...ure%203755.jpg
-
been following your work from the begining, all I can say is incredible skill and attention to detail...
-
NIce work!!! I like your welding crutch Idea. That has to make it lots easier to get a nice weld.
Hind Sight is always 20/20. :)
Brian
-
Thanks for the comments fellas. The crutch definitely helps out..