Just joined? Please introduce yourself.
Classic Edge Designs, LLC Prime Custom Cars, LLC MadMooks

Search:

Type: Posts; User: Old Buzzard

Page 1 of 9 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    8
    Views
    196

    Til it rolls out from under you, and you eat a...

    Til it rolls out from under you, and you eat a rocker panel!:eek:
  2. Replies
    9
    Views
    958

    Flow chart

    LS engine.
  3. Replies
    9
    Views
    958

    U have the heater ports blocked off?

    U have the heater ports blocked off?
  4. Replies
    2
    Views
    395

    What is the intended function of the Fitech temp...

    What is the intended function of the Fitech temp wire?
    There should be a fan control output in the Fitech. Is it a ground or a 12V?
    I suspect it could be either. In any case, it'll be a low power...
  5. Replies
    9
    Views
    958

    Another pic.

    12048
  6. Replies
    9
    Views
    958

    "Anyway, still need to understand my...

    "Anyway, still need to understand my thermostat/water pump issue and find a thermostat which fits this water pump properly as I believe there should be clearance between the thermostat bypass shutoff...
  7. Replies
    9
    Views
    958

    "I was concerned when the engine temp started to...

    "I was concerned when the engine temp started to get over 200 and climbing so I shut it down."
    Modified stock harness?
    New temp sensor?
    Headers?
    How are you measuring this 200* temp?
  8. Replies
    3
    Views
    386

    We have one, a 51, in the shop for a major redo,...

    We have one, a 51, in the shop for a major redo, of a long list of screwups, by the so called "builder".
    15 yrs, at least $150K, and counting.. Never been driven, or much less even started up.
    This...
  9. Replies
    3
    Views
    726

    Nothing.. Just 1 too many, as it turns out. Not...

    Nothing.. Just 1 too many, as it turns out.
    Not any more. :)
  10. Replies
    3
    Views
    726

    55 fender holes?

    $$$##%
  11. Replies
    5
    Views
    751

    Shop manual have one?

    Shop manual have one?
  12. Replies
    19
    Views
    1,156

    Before you start adjusting anything, post a pic...

    Before you start adjusting anything, post a pic of the end of the master cyl, and the booster. Measure the diameter of the m/c bore.
    You have to check the free play on the pedal push rod and the...
  13. Replies
    3
    Views
    389

    V8 or 6 cyl?

    V8 or 6 cyl?
  14. Replies
    19
    Views
    1,156

    That's a start. We had 2 of those. 1 leaked @...

    That's a start.
    We had 2 of those.
    1 leaked @ the ft port.
    1 would not bleed.
    Both went back to summit.
    We use the Wilwood units w/ adj prop valves.
  15. Replies
    5
    Views
    678

    Ga Classic Chevy, Lilburn, GA. Terry Lee has...

    Ga Classic Chevy, Lilburn, GA.
    Terry Lee has been my go to guy for almost 40 yrs!
  16. Replies
    2
    Views
    391

    "The car runs and drives fine but the brakes...

    "The car runs and drives fine but the brakes aren't up to snuff."
    What leads you to think, that the lines are the cause of the brakes "not being up to snuff"?
  17. Replies
    3
    Views
    853

    Modified and installed. Had to change a mting...

    Modified and installed.
    Had to change a mting ear as it uses the stock pedal mount. It's gone.
    Also added another set of holes for more adjustment.
  18. Replies
    9
    Views
    758

    Answered on the other board???

    Answered on the other board???
  19. Replies
    2
    Views
    595

    Thanks! I think that's what I'll do. Masking...

    Thanks!
    I think that's what I'll do.
    Masking the parts shouldn't be a big deal.
    The static wrap works well for this.
    The pieces in mind, are items I can handle.
    Doing this prior to assembly.
  20. Thread: WTB

    by Old Buzzard
    Replies
    1
    Views
    583

    Disregard. Found what I needed.

    Disregard. Found what I needed.
  21. Replies
    2
    Views
    595

    Preferences?

    Paint first, then undercoat?
    UC first, then paint?
  22. Replies
    4
    Views
    772

    ^^ Remember that!:mad:

    ^^ Remember that!:mad:
  23. Replies
    3
    Views
    853

    Well, I've got it, and the pedal, on it's way....

    Well, I've got it, and the pedal, on it's way. We'll see.
  24. Replies
    8
    Views
    770

    So does "sneaky cream"!:D

    So does "sneaky cream"!:D
  25. Replies
    3
    Views
    853

    Anyone use this ?

    Looks to be a nice piece.
    I'm considering using the Holley Term Max, and need a specific pedal to use it.
    LS Engines | Our Store and Products | AVS Motorsports
Results 1 to 25 of 208
Page 1 of 9 1 2 3 4