Just joined? Please introduce yourself.

Search:

Type: Posts; User: Old Buzzard

Page 1 of 10 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    12
    Views
    1,828

    605 = BAD CHOICE! BTDT.

    605 = BAD CHOICE! BTDT.
  2. Replies
    10
    Views
    1,403

    So, I'd like a reliable ignition with a vacuum...

    So, I'd like a reliable ignition with a vacuum advance for a street cruiser. Thoughts?

    Small cap HEI?
  3. Country stores were our main source of lunch,...

    Country stores were our main source of lunch, when I ran the eastern mountains, in the mining equipment business.
    A little store, on the "2 lane", a lady making bologna sandwiches and an RC, or a...
  4. Replies
    26
    Views
    933

    Check the exh port location so you don't get in...

    Check the exh port location so you don't get in trouble with header fitment.
  5. Replies
    8
    Views
    893

    Til it rolls out from under you, and you eat a...

    Til it rolls out from under you, and you eat a rocker panel!:eek:
  6. Replies
    9
    Views
    1,620

    Flow chart

    LS engine.
  7. Replies
    9
    Views
    1,620

    U have the heater ports blocked off?

    U have the heater ports blocked off?
  8. Replies
    2
    Views
    588

    What is the intended function of the Fitech temp...

    What is the intended function of the Fitech temp wire?
    There should be a fan control output in the Fitech. Is it a ground or a 12V?
    I suspect it could be either. In any case, it'll be a low power...
  9. Replies
    9
    Views
    1,620

    Another pic.

    12048
  10. Replies
    9
    Views
    1,620

    "Anyway, still need to understand my...

    "Anyway, still need to understand my thermostat/water pump issue and find a thermostat which fits this water pump properly as I believe there should be clearance between the thermostat bypass shutoff...
  11. Replies
    9
    Views
    1,620

    "I was concerned when the engine temp started to...

    "I was concerned when the engine temp started to get over 200 and climbing so I shut it down."
    Modified stock harness?
    New temp sensor?
    Headers?
    How are you measuring this 200* temp?
  12. Replies
    3
    Views
    574

    We have one, a 51, in the shop for a major redo,...

    We have one, a 51, in the shop for a major redo, of a long list of screwups, by the so called "builder".
    15 yrs, at least $150K, and counting.. Never been driven, or much less even started up.
    This...
  13. Replies
    3
    Views
    1,271

    Nothing.. Just 1 too many, as it turns out. Not...

    Nothing.. Just 1 too many, as it turns out.
    Not any more. :)
  14. Replies
    3
    Views
    1,271

    55 fender holes?

    $$$##%
  15. Replies
    5
    Views
    1,072

    Shop manual have one?

    Shop manual have one?
  16. Replies
    19
    Views
    1,715

    Before you start adjusting anything, post a pic...

    Before you start adjusting anything, post a pic of the end of the master cyl, and the booster. Measure the diameter of the m/c bore.
    You have to check the free play on the pedal push rod and the...
  17. Replies
    3
    Views
    546

    V8 or 6 cyl?

    V8 or 6 cyl?
  18. Replies
    19
    Views
    1,715

    That's a start. We had 2 of those. 1 leaked @...

    That's a start.
    We had 2 of those.
    1 leaked @ the ft port.
    1 would not bleed.
    Both went back to summit.
    We use the Wilwood units w/ adj prop valves.
  19. Replies
    5
    Views
    954

    Ga Classic Chevy, Lilburn, GA. Terry Lee has...

    Ga Classic Chevy, Lilburn, GA.
    Terry Lee has been my go to guy for almost 40 yrs!
  20. Replies
    2
    Views
    578

    "The car runs and drives fine but the brakes...

    "The car runs and drives fine but the brakes aren't up to snuff."
    What leads you to think, that the lines are the cause of the brakes "not being up to snuff"?
  21. Replies
    3
    Views
    1,073

    Modified and installed. Had to change a mting...

    Modified and installed.
    Had to change a mting ear as it uses the stock pedal mount. It's gone.
    Also added another set of holes for more adjustment.
  22. Replies
    9
    Views
    1,105

    Answered on the other board???

    Answered on the other board???
  23. Replies
    2
    Views
    791

    Thanks! I think that's what I'll do. Masking...

    Thanks!
    I think that's what I'll do.
    Masking the parts shouldn't be a big deal.
    The static wrap works well for this.
    The pieces in mind, are items I can handle.
    Doing this prior to assembly.
  24. Thread: WTB

    by Old Buzzard
    Replies
    1
    Views
    751

    Disregard. Found what I needed.

    Disregard. Found what I needed.
  25. Replies
    2
    Views
    791

    Preferences?

    Paint first, then undercoat?
    UC first, then paint?
Results 1 to 25 of 237
Page 1 of 10 1 2 3 4