Just joined? Please introduce yourself.
Classic Edge Designs, LLC Prime Custom Cars, LLC MadMooks

Search:

Type: Posts; User: Rustaddict

Page 1 of 7 1 2 3 4

Search: Search took 0.05 seconds.

  1. how did you blow your original rear end ?

    how did you blow your original rear end ?
  2. Replies
    3
    Views
    861

    Just shooting off the hip, are you sure your...

    Just shooting off the hip, are you sure your timing is right? Have you tried advancing it a little more to see if theres an improvement?
  3. Replies
    18
    Views
    2,808

    I second that.

    I second that.
  4. Replies
    812
    Views
    280,473

    Sticky: Robert, Are you making your door panels out of...

    Robert, Are you making your door panels out of sheet metal ?
  5. Replies
    31
    Views
    6,775

    That is a good looking car. You've got something...

    That is a good looking car. You've got something there to be proud of
  6. Replies
    9
    Views
    1,715

    I have no experience with either.

    I have no experience with either.
  7. Replies
    9
    Views
    1,715

    To the best of my knowledge, no one is making a 9...

    To the best of my knowledge, no one is making a 9 passenger fuel tank. You'll have to repair what you have. If I were using the 97 vortec and auto trans, I'd put an intake manifold & carburetor on it...
  8. Replies
    7
    Views
    1,342

    yes the water pump turns backwards on factory set...

    yes the water pump turns backwards on factory set ups. Not sure about aftermarket set ups.

    I always believed that ideally the fan shroud dictated how far from the radiator the fan should be. I...
  9. Replies
    7
    Views
    1,342

    Is it a used GM or aftermarket serpentine set up ?

    Is it a used GM or aftermarket serpentine set up ?
  10. Replies
    40
    Views
    5,819

    I dont think having a 57 linkage has anything to...

    I dont think having a 57 linkage has anything to do with the oil filter clearance. The benefit of the 57 stuff is it is a better design than the first 2 years. You need a 57 Z bar if you get 57 lower...
  11. Replies
    33
    Views
    5,994

    You're welcome. I was just kidding I know a few...

    You're welcome. I was just kidding I know a few people. One thing I will add is I had to take a die and cut the threads a little farther down the shaft and shorten the threaded end of the rod a...
  12. Replies
    33
    Views
    5,994

    I dont have any friends. I was doing the best I...

    I dont have any friends. I was doing the best I could with what I have to work with.
  13. Replies
    33
    Views
    5,994

    The throttle is wide open. I was by myself and...

    The throttle is wide open. I was by myself and checking for wide open throttle when I floored the gas and since I could'nt be at the carb and on the gas pedal at the same time, I leaned out of the...
  14. Replies
    33
    Views
    5,994

    For comparison's sake heres mine. I have the east...

    For comparison's sake heres mine. I have the east coast chevy rod. 11673
  15. Replies
    4
    Views
    945

    Could you open the hole up a little bit and go...

    Could you open the hole up a little bit and go with the 7/16 bolt ?
  16. Replies
    33
    Views
    5,994

    East Coast Chevy ( and others ) sell the correct...

    East Coast Chevy ( and others ) sell the correct rod that goes from the firewall rod to the carb. I'm using that replacement rod on a Holley with no trouble.
  17. We used to have a place local that taught...

    We used to have a place local that taught disadvantaged people trades and they did sandblasting fairly cheap. Maybe you could spot blast the rust and scuff the rest. I live on the east coast and salt...
  18. Replies
    40
    Views
    5,819

    The thing is, the clearance is so tight between...

    The thing is, the clearance is so tight between the floor and the bench seat that it dosent really leave much room for the modifications you'd need to do. If your money is tight, it is possible to...
  19. Replies
    18
    Views
    2,808

    Sweet. How much do you know about it?

    Sweet. How much do you know about it?
  20. I have use both over self etching primer and they...

    I have use both over self etching primer and they seemed to hold up well. This was before I knew epoxy primer existed and there's no doubt that Epoxy primer is the superior product to use these days....
  21. Replies
    40
    Views
    5,819

    Here's another suggestion to buy new 57 clutch...

    Here's another suggestion to buy new 57 clutch linkage and be done with it
  22. Awlgrip is some of the toughest paint I know of...

    Awlgrip is some of the toughest paint I know of at the moment. Imron isnt much better than Nason anymore in my opinion.
  23. You should be able to put about anything you want...

    You should be able to put about anything you want over that self etching primer. I would refrain from topcoating with the SPI like you mentioned. I'm sure they have a good reason for saying not to....
  24. Replies
    8
    Views
    1,609

    a lot of times the frames are rusty by now. Thats...

    a lot of times the frames are rusty by now. Thats probably not a bad idea.
  25. Replies
    8
    Views
    1,609

    I am surprised how much I like that solid white!....

    I am surprised how much I like that solid white!. It looks like you have a fairly solid driver that you can still enjoy while you improve on it. You should be able to find a glass shop that will cut...
Results 1 to 25 of 172
Page 1 of 7 1 2 3 4