Just joined? Please introduce yourself.
Classic Edge Designs, LLC Prime Custom Cars, LLC MadMooks

Search:

Type: Posts; User: Old Buzzard

Page 1 of 9 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    315

    Check the exh port location so you don't get in...

    Check the exh port location so you don't get in trouble with header fitment.
  2. Replies
    8
    Views
    488

    Til it rolls out from under you, and you eat a...

    Til it rolls out from under you, and you eat a rocker panel!:eek:
  3. Replies
    9
    Views
    1,202

    Flow chart

    LS engine.
  4. Replies
    9
    Views
    1,202

    U have the heater ports blocked off?

    U have the heater ports blocked off?
  5. Replies
    2
    Views
    485

    What is the intended function of the Fitech temp...

    What is the intended function of the Fitech temp wire?
    There should be a fan control output in the Fitech. Is it a ground or a 12V?
    I suspect it could be either. In any case, it'll be a low power...
  6. Replies
    9
    Views
    1,202

    Another pic.

    12048
  7. Replies
    9
    Views
    1,202

    "Anyway, still need to understand my...

    "Anyway, still need to understand my thermostat/water pump issue and find a thermostat which fits this water pump properly as I believe there should be clearance between the thermostat bypass shutoff...
  8. Replies
    9
    Views
    1,202

    "I was concerned when the engine temp started to...

    "I was concerned when the engine temp started to get over 200 and climbing so I shut it down."
    Modified stock harness?
    New temp sensor?
    Headers?
    How are you measuring this 200* temp?
  9. Replies
    3
    Views
    473

    We have one, a 51, in the shop for a major redo,...

    We have one, a 51, in the shop for a major redo, of a long list of screwups, by the so called "builder".
    15 yrs, at least $150K, and counting.. Never been driven, or much less even started up.
    This...
  10. Replies
    3
    Views
    930

    Nothing.. Just 1 too many, as it turns out. Not...

    Nothing.. Just 1 too many, as it turns out.
    Not any more. :)
  11. Replies
    3
    Views
    930

    55 fender holes?

    $$$##%
  12. Replies
    5
    Views
    905

    Shop manual have one?

    Shop manual have one?
  13. Replies
    19
    Views
    1,415

    Before you start adjusting anything, post a pic...

    Before you start adjusting anything, post a pic of the end of the master cyl, and the booster. Measure the diameter of the m/c bore.
    You have to check the free play on the pedal push rod and the...
  14. Replies
    3
    Views
    455

    V8 or 6 cyl?

    V8 or 6 cyl?
  15. Replies
    19
    Views
    1,415

    That's a start. We had 2 of those. 1 leaked @...

    That's a start.
    We had 2 of those.
    1 leaked @ the ft port.
    1 would not bleed.
    Both went back to summit.
    We use the Wilwood units w/ adj prop valves.
  16. Replies
    5
    Views
    800

    Ga Classic Chevy, Lilburn, GA. Terry Lee has...

    Ga Classic Chevy, Lilburn, GA.
    Terry Lee has been my go to guy for almost 40 yrs!
  17. Replies
    2
    Views
    472

    "The car runs and drives fine but the brakes...

    "The car runs and drives fine but the brakes aren't up to snuff."
    What leads you to think, that the lines are the cause of the brakes "not being up to snuff"?
  18. Replies
    3
    Views
    946

    Modified and installed. Had to change a mting...

    Modified and installed.
    Had to change a mting ear as it uses the stock pedal mount. It's gone.
    Also added another set of holes for more adjustment.
  19. Replies
    9
    Views
    925

    Answered on the other board???

    Answered on the other board???
  20. Replies
    2
    Views
    682

    Thanks! I think that's what I'll do. Masking...

    Thanks!
    I think that's what I'll do.
    Masking the parts shouldn't be a big deal.
    The static wrap works well for this.
    The pieces in mind, are items I can handle.
    Doing this prior to assembly.
  21. Thread: WTB

    by Old Buzzard
    Replies
    1
    Views
    676

    Disregard. Found what I needed.

    Disregard. Found what I needed.
  22. Replies
    2
    Views
    682

    Preferences?

    Paint first, then undercoat?
    UC first, then paint?
  23. Replies
    4
    Views
    880

    ^^ Remember that!:mad:

    ^^ Remember that!:mad:
  24. Replies
    3
    Views
    946

    Well, I've got it, and the pedal, on it's way....

    Well, I've got it, and the pedal, on it's way. We'll see.
  25. Replies
    8
    Views
    896

    So does "sneaky cream"!:D

    So does "sneaky cream"!:D
Results 1 to 25 of 215
Page 1 of 9 1 2 3 4