Just joined? Please introduce yourself.
Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: Gas Gauge Fluctuates

  1. #1
    Registered Member Belair-o's Avatar
    Join Date
    Jun 2013

    Member #:1723
    Location
    Franktown, CO
    Posts
    597

    Gas Gauge Fluctuates

    When my car is running, the gas gauge needle fluctuates periodically, moving up to 1/8th of a tank. This happens even when the car is not moving. Any ideas on a fix that might settle down the gauge? I posted this in the modified forum because the gauge is not stock - it is a Westach gauge.
    Thanks, Doug

  2. #2
    Registered Member
    Join Date
    May 2012

    Member #:625
    Posts
    3,409
    On of mine not sure does something similar, not sure if is my 55 or 56 or both. they have oem gauges.

  3. #3
    Registered Member BamaNomad's Avatar
    Join Date
    Nov 2016

    Member #:3217
    Location
    Rocket City, USA (Huntsville, AL area)
    Posts
    3,774
    A small filter across the gauge should prevent fast fluctuations in the voltage to the gauge...

  4. #4
    Registered Member
    Join Date
    Feb 2018

    Member #:3682
    Location
    Huntsville, AL
    Posts
    399
    might check power, ground and wire connections, too

  5. #5
    Registered Member
    Join Date
    Apr 2012

    Member #:571
    Posts
    4,671
    Voltage variation shouldn't affect the gauge output, as a voltage limiter is part of the circuit internal to the gauge. On the other hand, it could be in disrepair.

  6. #6
    Registered Member
    Join Date
    Feb 2018

    Member #:3682
    Location
    Huntsville, AL
    Posts
    399
    I thought the gas gauges were ammeters, the tank sender being a variable resistor. Thus, a change in voltage would change the current, thus the dial. What am I missing, Rick

  7. #7
    Registered Member
    Join Date
    Apr 2012

    Member #:571
    Posts
    4,671
    You aren't missing anything. Voltage is supposed to be constant, resistance of the sender is the desired variable, and the current is what reads on the gauge movement. An undesired variable is voltage, if it changed you would have a false reading. That's why the gauge has the voltage limiter built into it.
    Last edited by Rick_L; 11-30-2021 at 07:52 PM.

  8. #8
    Registered Member Belair-o's Avatar
    Join Date
    Jun 2013

    Member #:1723
    Location
    Franktown, CO
    Posts
    597
    Hi TriFivers,
    Thanks for the replies and discussion. At the end of the day, I don't understand if you think there are some things I should try to fix the gauge fluctuating response. I will look at the connections, as TriFiveRichard suggested.

    If, as Rick says the voltage limiter in the gauge was faulty, could I remotely add a limiter in the sender wiring. Not sure what limiter (or filter?) might be incorporated.

    BTW, I read where sometimes it is suggested to have a ground from the sender to the frame or body, but I assume this is for instances where the gauge doesn't work at all due to no ground. If you think it might help, I will add that ground. Rather than run the ground from sender to frame/body, what if I drilled a hole in the corner of the tank flange and connected there. The sender doesn't leak a drop, and I am reluctant to monkey with it.
    Thanks, Doug

  9. #9
    Registered Member
    Join Date
    May 2012

    Member #:625
    Posts
    3,409
    If I have learned anything about gas gauges over the years its they need a good clean ground.

  10. #10
    Registered Member Belair-o's Avatar
    Join Date
    Jun 2013

    Member #:1723
    Location
    Franktown, CO
    Posts
    597
    Sorry to be slow and ignorant, but wondered if you had any replies to the questions I asked (please see below). I looked at the connections, and they all look good. I haven't added an additional ground, yet. Don't know if my thought of grounding the tank from the corner of the tank is dumb (reasons stated below). I don't know if I can put a voltage limiter in the circuit in a remote location (like near the tank), to test the concept. I don't know what an appropriate voltage limiter would be.
    Thanks for your consideration. Doug
    Quote Originally Posted by Belair-o View Post
    Hi TriFivers,
    Thanks for the replies and discussion. At the end of the day, I don't understand if you think there are some things I should try to fix the gauge fluctuating response. I will look at the connections, as TriFiveRichard suggested.

    If, as Rick says the voltage limiter in the gauge was faulty, could I remotely add a limiter in the sender wiring. Not sure what limiter (or filter?) might be incorporated.

    BTW, I read where sometimes it is suggested to have a ground from the sender to the frame or body, but I assume this is for instances where the gauge doesn't work at all due to no ground. If you think it might help, I will add that ground. Rather than run the ground from sender to frame/body, what if I drilled a hole in the corner of the tank flange and connected there. The sender doesn't leak a drop, and I am reluctant to monkey with it.
    Thanks, Doug

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •